HVAC School - For Techs, By Techs

Sleeve vs. Ball Bearings - Short 127

In today’s short podcast, Bryan explains the differences between sleeve and ball bearings. Techs often make some avoidable mistakes because they either don’t know the difference between the two or don’t notice the bearing type on their equipment. On a basic sensory level, ball bearings tend to be louder than sleeve bearings. So, if you replace a sleeve bearing motor with a ball bearing motor, then excess noise may not indicate any problems after all. Lubrication is usually more consistent ...

Horizontal Scroll Compressors w/ Trevor

In today’s podcast, Trevor Matthews from Emerson talks about horizontal scroll compressors. Throughout the podcast, we refer to Bulletin AE4-1338 (R3). You can find that bulletin HERE. Horizontal scroll compressors are common in mobile applications, like buses and trains. They’re shorter in height than other compressors, so they fit into tighter spaces and are ideal for transport refrigeration. Scroll compressors are particularly susceptible to overheating, and you need some controls to...

Buck & Boost Autotransformers - Short 126

In today’s short podcast, Bryan discusses buck-boost (auto) transformers and what they do. Autotransformers are not automatic; the “auto” prefix comes from the fact that autotransformers only have one inductive winding. That winding is shared by the primary and the secondary, so it is not an isolation-type transformer. These transformers run current through the same winding used for induction. Buck-boost transformers rise or decrease voltage. When the transformer “bucks,” it decreases vo...

An Effective IAQ Process w/ John Ellis

In today’s podcast, John Ellis joins Bryan to talk about indoor air quality (IAQ). He also explains the ideal process for providing IAQ solutions. John has a lot of experience working as a consultant for people who have respiratory issues, so he has valuable perspectives. The HVAC and IAQ fields intersect in the areas of thermal comfort, humidity, building pressures, ventilation, filtration, and source control (which pollutants are present, where they come from, and how we can remove them)...

Caring for Technician Mental Health

In today’s podcast, Scott Krasman from TZOA, Andrew Greaves, and Kaleb Saleeby join Bryan for a conversation about mental health in the trades. We have a greater awareness of mental health than we ever did before, and although some of us may make fun of the topic, it is something we should focus on as HVAC technicians and business owners. “Toxic” is a common buzzword these days, but it’s relevant here. A work environment with toxic traits will wear you down over time as you are exposed to ...

Troubleshoot the System! w/ Jim Bergmann

In today’s podcast, Jim Bergmann talks about troubleshooting the entire system. He takes a holistic approach to the art of troubleshooting, NOT just an equipment-centered one. According to NIST, the most common HVAC system problems are duct leakage, refrigerant undercharge, and oversized equipment (often for undersized ducts). Duct leakage heavily affects the envelope; the equipment only plays a part in conditioning a space. As such, you will want to seal up holes that lead to unconditio...

How to Measure Total System Airflow w/ Steven

In today’s podcast, Steven Rogers joins Bryan to talk about measuring total system airflow. Fluid measurement is NOT restricted to liquids; a fluid is anything that flows, including liquids and gases. In HVAC, we deal with both of them, but airflow is strictly limited to the flow of gas. The airflow we experience in HVAC is exclusively turbulent flow, NOT truly laminar flow. Total system airflow is difficult to measure directly; we can use flow hoods, but they have their limitations, esp...

HVAC/R Career Advancement - Short 125

In today’s short podcast, Bryan explains how growth happens in an HVAC/R career. He also gives tips to get “unstuck” if you feel like you aren’t moving forward. You won’t move forward if you haven’t set a goal to move forward. Making a “vision board” helps you determine what matters in your life, and it helps you clarify what you’ll need to do in order to achieve your life goals. That way, you can use your career to help achieve those goals and see whose support you need. Having a growth...

Mini-Split Controls Strategy w/ METUS

In today’s podcast, Bryan and a team of Mitsubishi Electric Trane HVAC US (METUS) managers (Mike Schaefer, Charles Miltiades, and Sly Grimm) discuss mini-split controls strategies. Some contractors misunderstand what mini-splits are. Mini-splits CAN be ductless, but not all of them are ductless. Mini-split systems also have handheld controls, but those are not the only control options for mini-splits. Mini-split controls also come in wi-fi, wall-mounted, and wired varieties. Another comm...

Key System Performance Factors - Short 124

In today’s short podcast, Bryan discusses the key factors for system performance WITHOUT doing a deep dive into system commissioning. “Performance” refers to system efficiency, capacity, air filtration/cleanliness, longevity, and the ability to match the latent and sensible loads of a space. System airflow is the main performance factor to consider. To determine proper airflow (CFM), consult Manuals S, J, and D to perform calculations. In general, the absolute lowest limit is around 275 CF...

Copeland Scroll Compressor Multiples for Air Conditioning w/ Trevor

In today’s podcast, Trevor and Bryan discuss Copeland Scroll Compressor Multiples for Air Conditioning. “Multiples” refer to equipment setups with multiple compressors that have connected suction and discharge lines, so they resemble parallel rack refrigeration setups. Multiples typically come in tandem (2) or trio (3) sets. Compared to having a single giant compressor, multiples are more efficient, more reliable, and have the ability to keep running in case if there’s a compressor failure...

Margin, COGS, Markup & Profit Confusion - Short 123

In today’s short podcast, Bryan clears up the differences between markup and profit margins in HVAC businesses. The number one mistake that people make in business is confusing markup and gross margin. For example, you can double the price of a $50-part and sell it for $100. That would be a 100% markup. However, your gross margin is NOT 100%; your gross margin is only 50%; you only made a 50% profit on the total sale.  In the same case you have above, you have a 50% cost of goods sold (C...

Planning and Layout of HVAC Projects

In today’s podcast, Eric Mele and Bryan explain the planning, layout, and execution of HVAC projects. They mostly cover commercial ductwork but also touch on piping and some residential projects. Planning The first step is to review the construction plan WITH a site visit. It is best to see how a plan works within the space; plans may be feasible on paper but may not work out as planned in the actual space.  During the site visit, you also want to establish solid communication with eve...

Startup vs commissioning - Short 122

In today’s short podcast, Bryan explores the differences between startup and commissioning. Startups typically involve going in during the construction phase after the drywall has been sealed up. (Vents, ducts, and copper piping typically go in before the drywall.) A technician can then perform a startup. The startup includes testing the drain line, checking the charge, checking for leaks, and seeing if the equipment performs its most basic function. (Does the gas furnace make flame? Does ...

How to Make Mentorship Work w/ Eric Kaiser

In today’s podcast, Eric Kaiser and Bryan talk about mentorship in the HVAC industry. They discuss what it means to be a good mentor, how to find a good mentor, and what it means to be mentored.  Mentorship is an organic process. Most mentees don’t go up to someone they respect and formally ask that person to be their mentor. Respect is the foundation of the mentor-mentee relationship; formal mentorship often resembles friendship in many ways.  However, mentorship can take more forms tha...

Alternatives for College That Parents Should Consider

In today’s podcast, Bryan explores the upsides of choosing a career in the skilled trades instead of going to college. He also covers ways to prepare your child for a trades education and career while they are still deciding what to do with their lives. When we think about what we want for our kids, the following goals come up quite often: purpose, financial upside and reward, freedom from debt, and joy. The trades can offer a lifestyle that covers all of these bases. However, the opinions...

Triple Evacuation - Short 121

In today’s short podcast, Bryan explores triple evacuation. Many people believe that we don’t like triple evac, but that’s simply NOT true. We’re here to set the record straight. If the manufacturer tells you to follow triple evacuation processes, then it’s a good idea to do what they say. We won’t argue with that. However, our argument is that the procedure can be more time-consuming than it’s worth when it’s NOT necessary. Deep vacuum technically counts as a vacuum pulled below 500 mic...

How to Teach the Physics of Everyday Life

In today’s podcast, Bryan explains how he teaches physics. He believes that teaching physics is about continuously building a mental model, and he covers the methods and mindsets that facilitate that learning style.  The basic Wikipedia definition of physics states that it is a science that deals with matter, energy, and their interactions. Even then, we can simplify “matter” to “stuff.” Simplifications like these help students feel more familiar with the subject and NOT feel intimidated b...

Be Careful With Cold Tanks - Short 120

In today’s short podcast, Bryan explores the dangers of cold tanks during refrigerant recovery. Whenever you have a recovery tank, you only want to fill it to 80% capacity in the liquid state. The same goes for all sorts of vessels (coils, etc.).  However, capacity isn’t the only factor to consider for safety. We need to know what our maximum temperature will be. You will be in greater danger of overfilling a tank when it is cold because higher temperatures increase the pressure. High pr...

Dehumidification Facts w/ Nikki

In today’s podcast, Nikki and Bryan discuss dehumidification. They cover the relationship between cooling and dehumidification, humidity control, and dehumidifier installation practices. If the A/C unit is the king, the dehumidifier is the queen. The A/C unit controls cooling and humidity, but it can only do so much. A dehumidifier helps the A/C manage comfort under more demanding conditions. Many factors contribute to comfort, including sensible heat ratio (SHR), relative humidity (RH), a...

TXV Troubleshooting w/ Trevor

In today’s podcast, Trevor and Bryan discuss how to troubleshoot thermostatic expansion valves (TXVs/TEVs). They also dive into the various types, applications, and components of TXVs. TXVs are metering devices that control evaporator superheat to protect compressors from harm. Controlling heat also regulates pressure, which improves efficiency and prevents issues like floodback and overheating. TXVs contain several components that manage the forces that open and close the valve. These com...

Push Pull Recovery - Short 119

In this short podcast episode, Bryan discusses push-pull recovery, how it works, and what we need to know about it. Push-pull recovery is a somewhat counterintuitive method of recovering liquid rapidly. We simply do that by pulling refrigerant out of the system and pushing it into the tank. However, when we pack refrigerant into a tank, the tank pressure and temperature increase. So, it can be more difficult to get refrigerant into the tank as the job goes on. When we recover liquid refr...

Small System Vacuum Tip - Short 118

In this short podcast episode, Bryan goes over one of his most valuable tips for pulling a vacuum on a small system. It can be very difficult to pull a vacuum on a small system, especially when you're dealing with a low-temperature application like a freezer. When you pull a vacuum, you're creating a low-pressure area that affects molecule behavior. So, you're creating a situation where the molecules push their way out of the system and into your vacuum pump. The low temperature and small ...

How to END Callbacks

In this podcast episode, Bryan and Eric Mele explain how HVACR technicians can END callbacks with a few best practices. Rushing through calls will often lead to callbacks. One of the most common mistakes techs make is failing to check the condensate drain before walking away from a job. To end callbacks, technicians would be wise to check the entire system and note any possible problem areas; in commercial HVAC and refrigeration, pay attention to variation across evaporators, condensers, a...

Compressor Overheating Diagnosis & Prevention

In this podcast episode, Bryan and Eric Mele discuss the diagnosis and prevention of compressor overheating in HVAC and refrigeration. The main causes of compressor overheating are inadequate cooling back to the compressor, low charge, restrictions, and sometimes even poor suction line insulation. We want to keep the suction temperature low while maintaining appropriate superheat. If the suction line temperature is too high, the compressor can't cool down well enough. Dirty condenser coils...

Re-tapping Transformers - Short 117

In this short podcast episode, Bryan and Eric Mele talk about re-tapping transformers for single-phase equipment in 208v applications. Most single-phase equipment can work for 230v or 208v, meaning that they can operate with low voltage. However, we typically see 208v in commercial buildings. The sine waves of 208v equipment are 120 degrees out of phase, not 180 degrees (as in split-phase applications). We get lower voltage from leg to leg (208v, though the voltage can be a little higher o...

Indoor Air Quality Map & Compass w/ TZOA

In this podcast episode, Ben Reed from TZOA, a disruptive air technology brand, joins us to discuss the indoor air quality map and compass. We spend a majority of our lives indoors, so TZOA tries to improve IAQ in homes to keep us healthier. HVAC manages airborne chemicals, so indoor air quality ties right into our industry; HVAC technicians will become more valuable when they become well-versed in IAQ technologies. In residential HVAC, we are already used to listening to customer compla...

Copeland 2-stage ZPS Scroll Compressors

In this podcast episode, Bryan and Trevor Matthews of Emerson Canada discuss the Copeland 2-stage ZPS scroll compressors. Please join us by following along in bulletins AE4-1428 and AE4-1365. The ZP91KCE to ZP143KC Copeland compressors don't have internal pressure reliefs (IPRs). Those higher-pressure compressors make very loud noises when they go off, and it'll blow hot discharge gas on the internal overload to shut down the compressor. Some scroll compressors have temperature operating...

Screw Compressor Talk w/ Vilter

In this podcast episode, Bryan, Trevor Matthews, and Jim Dick of Emerson talk about the screw compressor and how it works. This time, they focus on the Vilter single-screw compressors. Vilter is an industrial compressor division of Emerson (compare to Copeland). Vilter also makes reciprocating compressors, but the screw compressor is its claim to fame; you may want to consider using a screw compressor when you want greater capacity and control than a reciprocating compressor. Screw compres...

Condensation Problem Solving - Short 116

In this short podcast episode, Bryan talks about condensation and how HVAC technicians can solve condensation-related problems. He also discusses humidity control and how that can affect sweating. We may have heard the phrase, "Condensation is where hot meets cold." That's not necessarily true; while it may seem that sweating happens where hot meets cold, the dew point is the main cause. We won't see condensation unless we have air that reaches the dew point. When air flows across surfaces...

ECM Types and Applications

In this podcast episode, Bryan and Chris Mohalley of Regal Beloit discuss the different types of ECM. They also cover applications where you can expect to find ECMs. In the HVAC industry, we typically use three types of motors: constant-torque, constant-airflow, and constant-speed. Every ECM works on electronic commutation, so constant-torque motors use that to maintain torque output (X13). The constant-airflow motor is also known as the variable-speed motor, and it is one of the first ECM...

The Right and Wrong Way to HVACR w/ Eric Kaiser

In this podcast episode, Bryan and Eric Kaiser discuss the right and wrong way to do HVAC/R jobs and approach HVAC/R work. Breaking things down into "right" and "wrong" categories is a rather simple way to approach a problem; we throw nuance and alternatives out the window, which can be worse than doing something "wrong." Instead of viewing things as right and wrong, we would be better off if we looked at our objectives and focused on solving problems instead of being right. Although the...

How EC Motors Work

In this podcast episode, Bryan and Chris Mohalley from Regal Beloit discuss EC motors. They also describe ECM applications and how those motors work. EC motors (ECMs or "ECM motors") are electronically commutated motors. These motors are generally three-phase AC motors operated by a drive; that drive is a combination of an AC-to-DC converter, microprocessor, and frequency drive. So, the frequency delivered to the motor is generated electronically. When it comes to inputs, the ECM works l...

Stacking Liquid vs. Mechanical Subcooling - Short 115

In this short podcast episode, Bryan compares strategies for increasing the subcooling, including stacking liquid and mechanical subcooling. Subcooling is a consequence of condensing; when we change the refrigerant from a vapor to a liquid, it will drop below saturation temperature after it becomes completely liquid. There are three phases in the condenser: desuperheating, condensing, and subcooling. The first few rows of the coil reduce the superheat of the vapor entering the condenser. O...

Proper Design For Ductless and Ducted HVAC Systems

In this podcast episode, Bryan, Chad, John, and Allison discuss proper design for ductless and ducted HVAC systems, especially mini-splits. They also discuss potential future improvements to equipment and duct designs. Mini-splits are smaller than traditional HVAC units, so they make zoning a bit easier. However, load calculation plays a huge role in equipment selection and zoning because you must get the right number of zones to match the equipment capacity and meet your load requirements...

Atmospheric Pressure - Short 114

In this short podcast episode, Bryan explains what atmospheric pressure really is, pressure units and conversions, and why those are matter. Atmospheric pressure is the weight of the air around us pushing down on us. We normally see that value expressed as 14.7 PSI (or 0 PSIG). Before we dive too deep into atmospheric pressure, we should understand some basic pressure units. We may see pressure expressed in microns when we're pulling a vacuum; we are trying to pull the atmosphere out of ...

Diagnose and Prevent Compressor Short Cycling

In this podcast episode, Bryan and Trevor Matthews discuss compressor short cycling. They discuss how to diagnose and prevent that issue. Trevor and Bryan primarily refer to the Bulletin AE17-1262 throughout this episode, which you can find HERE. Compressor misdiagnosis is very common, but we generally encounter two types of compressor failures: electrical failures and lubrication failures. Short cycling causes a loss of oil in the compressor, which may lead to lubrication-related failure...

Recovery Tips and Best Practices w/ AC Service Tech

In this podcast episode, Bryan and Craig Migliaccio (AC Service Tech) discuss some HVACR recovery tips and best practices. When you select a recovery tank, you need to know which refrigerant is in the tank. So, it's a good idea to make sure you label each recovery cylinder. You don't want to contaminate refrigerant in the recovery tank, use a recovery tank with contaminated refrigerant, or have too much air inside the cylinder. If the tank is empty, you'll have to pull a vacuum on it befor...

Swaging and Flaring Tips w/ AC Service Tech

In this episode, Bryan and Craig Migliaccio (AC Service Tech) talk about some best practices you can use while swaging and flaring copper. There are a few different ways you can flare copper. Craig likes using a round deburring tool before flaring the copper. After the burr has been cleanly removed, Craig likes using an eccentric flaring tool for the actual flaring. Bryan's favorite flaring tool is the NAVAC battery-powered flaring tool for quick, accurate flares. Both Craig and Bryan agre...

Are Contactors Obsolete? (SureSwitch)

In this podcast episode, Bryan and Jim Fultz discuss the White-Rodgers SureSwitch and determine whether contactors are obsolete or not. Contactors are electrical controls; they started off very expensive and usually outlasted equipment, so they are currently smaller, cheaper, and less durable than they used to be. Modern contactors have open contacts and are susceptible to insect damage. Sometimes, an electrical arc can cause contactor pitting, which can weld the points together and render...

Don't Miss The Tech Training Event

Other Uses for Nitrogen - Short 113

In this episode, Bryan and Craig Migliaccio (AC Service Tech) discuss all the ways that nitrogen can make your job easier. Nitrogen is an inert gas that we can use for purging refrigerant lines and completing scale-free brazing jobs. As techs, we should have at least one inert gas in our trucks to help us do the best job possible. We can use inert gases for purging refrigerant from tubing, flowing and preventing oxidation while brazing, and pressurizing a system for leak detection or a pre...

Is Ultrasonic Leak Detection Best?

In this podcast episode, Bryan and Craig Migliaccio, AC Service Tech, talk about ultrasonic leak detection. They discuss its effectiveness and if it's worth the hype. Ultrasonic leak detection works best when there's oil on the inside of the tubing; it works best when the system is equalizing after shutoff. Oil or moisture can create a squealing noise, which is an indicator of a leak. Ultimately, lack of success with ultrasonic leak detection comes down to user discomfort and a lack of pro...

Universal Defrost Controls w/ Jim Fultz

In this podcast episode, Jim Fultz with White-Rodgers joins us to discuss universal defrost controls. He also explains when and why you might use universal controls. Bryan and Jim cover a universal defrost control for heat pumps (Model #: 47D01U-843). You can follow along by reading the manual HERE. Universal defrost controls can replace OEM defrost controls. Universal controls are sometimes more readily available than OEM parts, so they can be good repair options.  The White-Rodgers univ...

Maybe Don't Buy New Tools - Short 112

In this short podcast episode, Bryan and Craig Migliaccio discuss why you maybe don't want to buy new tools. Whenever you get new tools, you have to account for a learning curve and potential change to your practices. Changing your practices and procedures isn't necessarily a bad thing, but you have to practice with the tool and account for different setup and cleanup procedures. However, once you find a good process, you don't want to mess with it too much. You will also want to account f...

How Craig Became "AC Service Tech"

In this podcast episode, we find out how Craig Migliaccio became "AC Service Tech." He makes educational materials and has even written a book. You can check out his website HERE and his YouTube channel, AC Service Tech, HERE. Craig got into the HVAC trade after coming from a construction background; he mostly worked on existing homes and had to handle some HVAC tasks. From there, he got into service and went headfirst into the HVAC industry by starting his own business: a carpentry and HV...

What Skills and Knowledge Should You Start With? - Short 111

In this short podcast episode, Bryan and Craig Migliaccio discuss the skills and knowledge you should have to start in the HVAC industry. Of course, basic mechanical skills and knowledge are important before you get into the HVAC trade. You'll greatly benefit from knowing where and how to hammer nails, tighten screws, and identify all sorts of tools. When getting into the HVAC industry, one of the low-hanging fruits that you need to consider is your sheet metal skills. Know how to cut shee...

Controlling Liquid Refrigerant in A/C

In this podcast episode, Bryan and Trevor Matthews of Emerson Canada discuss strategies for controlling liquid refrigerant in A/C and refrigeration systems. They also read through the AE22-1182 bulletin, which you can find HERE. Liquid refrigerant is one of the most common causes of compressor damage and even failure. It can also cause a loss of oil, which leads to reduced lubrication and subsequent damage. Compressors are vapor pumps, and they are not designed to handle much liquid refri...

TXV Power Element / Power Head - Short 110

In this short podcast episode, Bryan talks about the TXV power element or power head. He explains what it does and why it's important. A TXV power element threads onto the top of the valve, and it's where the sensing bulb attaches to the valve. It is the component that applies the opening force to the TXV. When you lose the charge in the element, it stops exerting an opening force on the valve. So, the valve completely shuts and doesn't allow refrigerant to get to the evaporator coil. Yo...

How to Value Engineer Better w/ Alex Meaney

In this episode, Bryan and Alex Meaney talk about value engineering. They discuss what it means to value engineer better when it comes to construction projects. Value engineering is about finding ways to reduce the costs of a project. However, we don't want to do a bad job or use extremely cheap materials just to bring the price tag down. In many cases, builders will want to reduce the cost as much as possible, but we also want to make sure the construction project works in the end. In oth...